LimePath GeoSuDS UV is a UV stable Resin Bound Surfacing system which is installed at 30mm/40mm depth onto a 4mm high performance triple layer system of geotextiles & a stabilisation geonet. This system reduces the need for a binder courses such as concrete and asphalt concrete (macadam) whilst still providing high permeability & strength. The structure allows rainwater to pass through being SuDS (Sustainable Urban Drainage Systems) compliant. With permeability rates of up to 850l/m²/m. LimePath GeoSuDS UV has a triple lock stabilisation layer which is thermally bonded on both sides to provide excellent drainage & filtration whilst helping to stabilize the decorative UV Resin Bound surface layer and Sub-base.
Available in a variety of colours LimePath GeoSuDS UV is ideal for both commercial & domestic pathways, nature walks and general pedestrian areas.
DOWNLOADS
- Technical Data Sheet
- Colour Swatch (Mix Blends)
- Base build ups
- Additional information
Technical Data Sheet
- LimePath GeoSuDS UV
- Slip Resistance
All LimePath GeoSuDS UV aggregate blends have been tested for slip resistance in wet and dry conditions.
Anti-Slip aggregate broadcast onto the surfacing during installation will significantly increase the slip resistance of the surface in the wet and on steep gradients without substantial change to appearance.
Resin & aggregate
LimePath GeoSuDS UV resin is a UV resistant resin and will not yellow on exposure to UV light. This is a more attractive option than some other types of resin which can yellow and dramatically alter the appearance of the finished surface. The resin is formulated using aliphatic HDI which will not deteriorate or become brittle when exposed to UV light when tested to BS EN ISO 16474-3 method A The performance and appearance of the finished surface is dependent on the aggregate used (see LimeGate Solutions LimePath GeoSuDS UV mix blend swatch sheet for colour options). The LimePath GeoSuDS UV Aggregate blends have been designed to achieve strength, resilience, porosity and decoration.
Please Note:
Natural aggregates may contain small amounts of iron which can produce rust staining when exposed to air and water; standard LimePath GeoSuDS UV blends contain aggregates selected for infrequency of incidence of staining but iron may be present in any natural aggregate. The presence of iron cannot be identified before use and Limegate Solutions cannot accept responsibility for any loss or damage suffered as a result of staining.
Features and benefits
- UV stable will not discolor or degrade
- Tested to slip resistant BS 8204-6
- SuDS compliant permeable paving 850 liters/m²/minute
- Natural & Recycled aggregate available
- 30mm/40mm depth install directly onto type 1 or 3
- Triple lock GeoNet to help base stabilization and water drainage
- All aggregates selected to reduce chances of rust appearing
- Foot traffic after 14-15 hours @ 20°c
- Manufactured to ISO 9001
- Made in UK
For more information on any of our products or services please visit us on the Web at: www.limegate.co.uk or email:
LimePath GeoSuDS UV Contractors
LimePath GeoSuDS UV is a specialist product and must only be applied by specialist applicators. Do not apply or allow it to be applied by contractors who do not possess the necessary experience.
Working Times & Temperatures
Working time is affected by temperature; at temperatures above the maximum recommended 25°c the pot life and working time may be insufficient to allow a wet edge to be maintained. Do not therefore proceed when product and/or air temperature exceeds recommendations. The air temperature must be monitored during application and work should stop when the temperature exceeds recommendations. Care must be taken to keep materials as cool as possible in warm weather.
At low temperatures 5°C and below the resin will not flow sufficiently to achieve a smooth finish and work should not proceed.
Substrate Requirements
LimePath GeoSuDS UV System is designed for foot traffic and after consultation occasional vehicle access traffic such as light infrequent maintenance vehicles or pedestrian two wheel mode of transportation. All resin bound products by nature will be vulnerable to heavy impact and high point loading. It is good practise that the product is subject to cleaning and maintenance and regularly inspected by the client or installer and maintained as required. Please see LimePath GeoSuDS UV O&M Manual for further maintenance information.
Please refer to:
Limegate Solutions LimePath GeoSuDS UV Base Build Up Sheets for individual substrate requirements
Site Attendance
When on site Limegate Solutions representatives are if asked, able to give a general indication of the correct method of installing Limegate Solutions products. It is important to bear in mind that Limegate Solutions is a supplier and not an application contractor and it is therefore the responsibility of the contractor and his employer to ensure he is aware of the correct practices and procedures to ensure the correct installation of the product and that liability for its correct installation is with the contractor and not with Limegate Solutions Ltd.
Product
specification
Product: LimePath GeoSuDS UV
Thickness: 30mm/40mm LimePath GeoSuDS surface course (dependant on required usage)
Aggregate: (select mix blend as required)
Installation: Limegate Solutions Approved FeRFA association member contractor
Supplier:
454 Eden House
New Hythe Lane
Aylesford
ME20 7UH
Tel: 01959 546 208
email:
Surfacing solutions
mix blends
Want to know more?
If there’s anything you’d like to know about our services, get in touch and ask us. We’re always happy to answer any questions.
Contact Limegate
Give us a call on 01959 546 208 or email to ask us any questions about our services.
